查看: 1393|回复: 3

How one can Install

发表于 2010-9-13 16:49:45 | 显示全部楼层 |阅读模式
Putting in automotive audio amps is without doubt one of the trickiest issues a newbie automotive audio installer can attempt. Automobile amp installation demands that each one kinds of panels be removed and that various wires be run all around the car. Putting in automobile audio amplifiers is a step-by-step process which I have outlined here. When you have any questions please contact me by clicking here. Please don't try a automobile amp set up if you're not comfortable with the process. Leave it to a professional. Now here are the steps on the right way to set up a automotive amp. There is also a wiring diagram below. NOTE: These instructions assume you have already physically mounted your amplifier to a solid, non-conductive floor (non-metallic). When you have not bought your energy wiring remember to read this article on selecting wire gauge for amplifiers.
 楼主| 发表于 2010-9-28 16:46:25 | 显示全部楼层

How to Set up a Aut

1. Determine what aspect of the car the battery is on. Disconnect the unfavourable battery terminal. In case you have a radio with a security characteristic (comparable to a Delco-Loc, Eclipse ESN, etc.) ensure you know the reactivation or security code before disconnecting the negative battery terminal.

2. Discover a spot to run the power wire through the firewall. Try to find an empty rubber grommet that hides an unused manufacturing facility hole. You'll be able to just put a gap in this grommet and run your wire through.

3. Car Audio Stepped Bit or Uni-BitIf there isn't a manufacturing unit gap you will want to make one. Get out the ability drill and metal drill bits. Earlier than drilling be sure to know the place the bit will end up as soon as it is via the firewall. I often make a small pilot gap after which improve the bit dimension until the outlet is large enough for my wire. If in case you have a stepped bit (i.e. Uni-Bit) that might be nice to make use of (see photo). I recommend them highly.
 楼主| 发表于 2010-9-28 19:38:34 | 显示全部楼层

Find out how to Set

4. Defend the drilled hole edges from rust with paint or an identical material.

5. Automotive Audio Rubber GrommetsInstall a rubber grommet (see photograph

) into the hole to protect the wire from chaffing (VERY IMPORTANT!). Caulk the hole between the inner diameter of the rubber grommet and the facility wire if needed to forestall water from working down the wire. Larger gauge wire akin to 1/zero will require a specialised grommet and a a lot larger hole. StreetWires makes these kind of two piece grommets which they name firewall bushings.

6. Run the cable from the inside of the car, by the hole and to the battery area, being very careful to keep away from pinch factors and shifting elements within the engine bay. It is easier to push 5-8ft of wire by the grommet than the opposite 15-20ft from the battery side. That is why you push the wire from the interior.
发表于 2010-11-21 10:53:44 | 显示全部楼层
您需要登录后才可以回帖 登录 | 注册


010-66113443 周一至周五:10:00 - 18:00

星城祖母绿旗下专业宝石交流论坛,汇集了数万条网友关于祖母绿知识的相关心得,提供专业的宝石相关知识介绍答疑,是珠宝首饰时尚达人、业内人士、消费者的首选珠宝聚集地。| 网站地图

Powered by Zumulv.Com! © 1990-2017 StarCityEmerald Inc.

QQ|小黑屋|手机版|简易模式|珠宝玉石论坛 ( 京ICP备13002152号 )|网站地图   

GMT+8, 2020-8-7 23:35 , Processed in 0.537846 second(s), 23 queries , XCache On.

快速回复 返回顶部 返回列表